Dryer / User Manual 7 / 28 EN Important safety and environmental instructions A Washing machine cannot be placed on the dryer. Pay attention to the above warnings during the installation on your washing machine. Installation Table for Washing Machine and Dryer Dryer Depth Washing Machine Depth 62cm 60 cm 54 cm 50 cm 49 cm 45 cm 40 cm 54 cm Can be. Your new washing machine You have chosen a Bosch washing machine. Please take a few minutes to read and become familiar with the advantages of your washing machine. To meet the high quality demands required by Bosch, every washing machine that leaves our factory is carefully checked to ensure that it functions correctly and is in perfect condition. The user manual USE ONLY GENUINE IFB SPARES & ACCESSORIES. Advancing the science of washing SENORITA DX. The washing machine must have been installed and connected properly (refer page 7) Your appliance was tested before leaving. Oct 24, 2019 Recent IFB Washing Machine questions, problems & answers. Free expert DIY tips, support, troubleshooting help & repair advice for all IFB Washing Machine products.
- Ifb Washing Machine User Manual Pdf 2 8
- Ifb Washing Machine User Manual Pdf Online
- Ifb Washing Machine Customer Care
- Ifb Washing Machine Repair Manual Pdf
Information codes may be displayed to help you better understand what is occurring with your Washer.
| ERROR IMAGE | MEANING | SOLUTION |
|---|---|---|
| Unbalanced load prevented your Washer from spinning. | Redistribute the load, press the Start/ Pause Button. | |
| Door is unlocked when Washer is running. | Press the Power button to turn off your Washer, then restart the cycle. If the code reappears, call for service. | |
| Door is open when Washer is running. | Close the door tightly and restart the cycle. If the code reappears, call for service. | |
| Your Washer failed to lock the door. | Close the door tightly and restart the cycle. If the code reappears, call for service. | |
| Water temperature control problem. (Heater Control problem) | Call for service. | |
| Your Washer has tried to fill but has not reached the proper water level. | Call for service. | |
| Water level sensor problem. | Call for service. | |
| The door will not unlock. | Make sure the door is firmly closed. Push the Power button to turn off your Washer, then turn it on again. If the code reappears, call for service. | |
| Your washer is not draining. It can also mean that the unit senses a small clog while draining. | 1) Turn off the unit and turn it on again. 2) Select only the Spin Cycle. 3) Press the Start/Pause to drain the water. | |
| Your Washer has tried to fill but was unsuccessful. | Make sure the water faucets are open all the way. Check for kinked hoses. Check the inlet screens on the fill hoses. | |
| Problem with control. | Call for service. | |
| A fault is detected in the water level sensor. | Call for service. | |
| Jammed Key. | Call for service. | |
| • Motor speed sensor problem. • High current detected. • Motor not running properly. | Restart the cycle pressing the Start/ Pause Button. If the code reappears, call for service. | |
| Temperature sensor problem. | Restart the cycle. If the code reappears, call for service. | |
| High/Low voltage detected. | Restart the cycle. If the code reappears, call for service. | |
| SilverCareTM control problem | Restart the cycle. If the code reappears, call for service. | |
| Too many suds are detected during the washing session. | To prevent it, cut down on detergents. |
Error: 1C
Solution: Check the water level sensor
- Power off and power the machine on after 2-3 minutes, and then try again.
- Depending on the model, the drain system drains water automatically. The POWER and START/PAUSE buttons may be disabled during this process.
Error: TC2
Solution: Check the temperature sensor on the dry air
- Power off and power the machine on after 2-3 minutes, and then try again.
Error: DC
Solution: The door is open
- Close the door and press START/PAUSE to resume operation
Error: DC1
Solution: Check the door switch.
- Power off and power the machine on after 2-3 minutes, and then try again
Error: LC
Solution: Check for water leaks
- Power the machine off and check the drain system for any leak. Once the leak is solved, power the machine on after 2-3 minutes.
- Depending on the model, the drain system drains water automatically. The POWER and START/PAUSE buttons may be disabled during this process
Error: FC
Solution: Check the fan motor
- Power off and power the machine on after 2-3 minutes, and then try again
Error: 4C
Solution: Check the water supply line
- Check for the connection of the water line (including water taps).
- Power off and power the machine on after 2-3 minutes, and then try again.
- Depending on the model, the drain system drains water automatically. The POWER and START/PAUSE buttons may be disabled during this process
Error: 4C2
Solution: Laundry needs protection because the water being supplied is too hot
- Make sure the cold and hot water taps are properly connected.
- Power off and power the machine on after 2-3 minutes, and then try again.
Error: 5C
Solution: Check the drain system.
Ifb Washing Machine User Manual Pdf 2 8
- Make sure the drain filter is not clogged.
- If the drain filter is clogged, clean the filter and restart the machine.
Error: HC
Solution: Check the washing heater.
- Power off the machine and contact a local Samsung service centre
Error: HC2
Solution: Check the drying heater.
- Power off and power the machine on after 2-3 minutes, and then try again.
Error: Ub
Solution: Check the spinning process
- The load may not be balanced inside the drum. Check the drum and make sure the load is balanced.
- Press START/PAUSE to resume operation, or power off and power the machine on after 2-3 minutes, and then try again
Error: 8C, 8C1, 8C2
Solution: Check the MEMS sensor
- Power off and power the machine on after 2-3 minutes, and then try again
Error: OC
Solution: Water may overflow
- Close the water valve and call for service
Error: 3C
Solution: Check the motor
- Power off and power the machine on after 2-3 minutes, and then try again
Error: AC6
Solution: Check the PBA communication status
- Power off and power the machine on after 2-3 minutes, and then try again
Error: DDC
Solution: The Add Door is open
- Close the Add Door and press START/PAUSE to resume operation
Error: DC3
Solution: Check the Add Door
Ifb Washing Machine User Manual Pdf Online
- Power off and power the machine on after 2-3 minutes, and then try again
Error: UC
Solution: Check the electronic control board
- Check if power is supplied properly.
- If the information code continues to appear, call for service.
A low voltage is detected.
- Check if the power cord is plugged in properly.
- If the information code continues to appear, call for service
| Error Code | Cause | Repair |
|---|---|---|
| E2 | Stuck key on control board | Try to free the key by gentle force. If you can't free the key, replace the user interface control board (also called the sub-PCB control board). |
| lE | Water level sensor failure | First, unplug the washer and check the wire harness connections between the water level sensor and the main control board. |
| nF | Water fill problem | If the washer takes 40 minutes or more to fill or if the water level doesn't change after six minutes, this code will appear. |
| LO or FL | Door lock error | Once the washer cycle is complete if the door fails to unlock after seven tries, you'll get the LO or FL code |
| dc | Unbalanced load | he dc code means the load has been detected as unbalanced during the final spin. |
| ds | Door is not locked | If the washer won't start ds signals that the washer door is open and the lock is malfunctioning. |
| OE | Overflow or too high water levels | A washer that is overfilled is usually caused by water inlet valves that are not shutting off the water flow properly. |
| nF1 | Hot and cold water lines are reversed | Connect the hot and cold water fill hoses correctly on the back of the washer. |
| tE | Water temperature is either too high or too low | Run the diagnostic test mode to check the water temperature that the control board is sensing. If the actual temperature is significantly different, the temperature sensor or thermistor should be replaced. |
| LE | Low water level during cycles | Water level drops can be caused by leaks in the washer tub or an improperly installed drain line which can siphon water out of the washer. |
| 3E | No signal from the drive motor tachometer | Unplug the washer. Check the wire harness connections on the drive motor and the electronic control board. |
| Hr | Heater relay failure | The heater relay is a component on the Main PCB control board. |
| 2E | Internal control board failure | Unplug the washer for 5 minutes to reset the electronic control board. Plug the washer back in. |
| SF | Main PCB error | Unplug the washer for five minutes to reset the electronic control board. |
| nd | Water will not drain | If the washer fails to drain within 15 minutes, check the washer drain filter and drain hose for a clog or restriction. |
| Sud (F70) | Too many suds | Using a regular detergent or even too much high-efficiency (HE) detergent will produce excessive suds. |
| AE | Communication error between the Main PCB and Sub PCB in the control panel | Check the wire harness connections between the PCB control boards in the control panel. |
How to Fix?
Samsung Washing Machine dC Error
- A- information code is displayed when the door is opened.
- B- Make sure the door is properly closed.
- C- Make sure that no laundry is caught in the door.
Samsung Washing Machine dC Error
Samsung Washing Machine 4C Error
- A-If your washer can’t be supplied water well, “4C” error message is displayed. When the washer displays the “4C” code, the washer do draining for 3 minutes. During this time, the Power button is inoperative.
- B- Make sure the water taps are open. Make sure the water taps are not frozen. Make sure the washing machine is operating with sufficient water pressure. (Optional) Make sure that the cold water tap and the hot water tap are properly connected.
- C- Make sure the water hoses are not clogged.
- D- Clean the mesh filter as it may be clogged.
Samsung Washing Machine 5C Error
- A- If your washer can’t drain well, [5C] error message is displayed.
- B- Make sure the drain hose is not frozen or clogged. Make sure the drain hose is positioned correctly, depending on the connection type. Make sure the drain hose is straightened all the way to the drain system.
- C- Clean the debris filter as it may be clogged.
Samsung Washing Machine 5C Error
Samsung Washing Machine Ub Error
Ifb Washing Machine Customer Care
- When Ub CODE is displayed, most vibration and noise issues are caused by the washing machine is not being level.
- Please Check the unit to make sure it is properly level. Never Install your washing machine on a carpet or other soft flooring surface.
- Please check the washer is not overloaded and redistribute the load if needed. If the washer is overloaded, remove some laundry.
- The 4 leveling legs should touch the floor all together.
How do I calibrate my Samsung Washer?
1.Using the Temp. and Delay End (+) buttons
Ifb Washing Machine Repair Manual Pdf
- Turn the washing machine off and then on again
- Hold down the Temp. and Delay End (+) buttons simultaneously for 3 seconds
- Press the Start/Pause button to begin Calibration Mode
2.Through the Settings
- Tap Settings on your washing machines display
- Tap Calibration
- Tap Start